SEAL Image 410 Instrukcja Naprawy

Image® 410 Laminator Owners Manual Image® 410 Laminator Owner’s Operation Manual

10LAMINATOR FEATURES Figure 4. Laminator Features 1. Digital Touch Pad Control Panel with LED indicators • It allows the operator to use 9 pre

11CONTROL PANEL 1. Nip Adjustment Button: Press the UP arrow once to raise one setting. Press and hold to raise multiple settings. Press the DOWN

12 7. Reverse Mode Button: Reverses the direction of the roller rotation. NOTE: The Reverse Mode Button may only be used with the footswitch and

13PRESET PROGRAMS Settings provided are for optimal performance using the SEAL® Brands films listed. Purchasers should individually determine, pri

14CHECKING OPERATION After you are familiar with the control panel and its functions, check all operations. WARNING! If your laminator does not oper

15SET-UP AND OPERATION TEMPERATURE SETTINGS • Select the film(s) that you will use on the top (and bottom) of the images. • Check which temperatu

16 SETTING THE UNWIND BRAKE TENSION IMPORTANT! The brake tension greatly affects the smooth flow of the laminating film. • Turning the unwind brake

17WEBBING FILMS WITHOUT A RELEASE LINER The following are the basic webbing procedures for webbing films without a release liner: • Select films sl

18WEBBING FILMS WITH A RELEASE LINER The following are the basic webbing procedures for webbing films with a release liner: • Select films slightl

19DECALING (HEAT-ACTIVATED) This process involves applying a hot film to the top and a cold backing adhesive to the bottom of the graphic. This pro

2TABLE OF CONTENTS TABLE OF CONTENTS...

20DECALING (PRESSURE- SENSITIVE) This process involves applying a cold pressure-sensitive over-laminate to the top and a cold pressure-sensitive mo

21MOUNTING This process involves mounting previously prepared decals onto a substrate. No films or adhesives are required for this process. TO MOU

22ONE STEP MOUNTING AND LAMINATING This process allows you to decal and mount in one step by using a mounting board with heat activated adhesive on

23ENCAPSULATING This process involves completely sealing an image between two films. It is important to follow the webbing instructions for films s

24PRE-COATING BOARDS This process is used to coat substrates with a self-adhesive coating onto which images can be mounted. Images can then be moun

25APPLYING AN OVERLAMINATE This process involves applying an over laminate to an image with the use of a sled or pre-coated substrate. PREPARATION

26PROCESS CONTROL SHEET Process: _________________________________ Application Use: ___________________________ Top Unwind Shaft:________________

27CLEANING / MAINTAINING YOUR LAMINATOR CLEANING THE LAMINATOR • The laminator may be cleaned with a lint-free cloth, lightly dampened with a mil

28PERIODIC MAINTENANCE SHEET CHAIN TENSION ADJUSTMENT / OIL CHAIN ** SAFETY CHECK AFTER SERVICING

29ERROR CODES THE FOLLOWING DESCRIBES THE DETAILS OF THE ERROR CODES: • The machine shuts down and the display starts blinking. • This means t

3INTRODUCTION Thank you for purchasing a SEAL® Image® 410 Laminator. We have designed the SEAL Image 410 to give you years of reliable service. The

30TROUBLESHOOTING GUIDE Problem Solution The laminator will not turn on. • Check if the power cable is plugged into the mains wall outlet. • Che

31 LOCATION OF BREAKERS • 1. Motor Breaker (0.8 Amp)– Located under the Right side plate. • 2. Control Power (2 Amp) – Located under the Left si

32GLOSSARY OF TERMS DECAL: An image that has been laminated on top (either heat-activated or pressure-sensitive) with an adhesive backing FILM: A

33SPARE PARTS LIST Please contact Technical Service for replacement parts. PART DESCRIPTION PART # Accessory Pack, 410 1162 Bracket, Bottom Main

34TECHNICAL SPECIFICATIONS MECHANICAL Dimensions (H x W x D) 62”w x 30”d x 47”h (157 cm x 76 cm x 119 cm) Net Weight 480 lbs. (218 kg) Shipping W

35LIMITED WARRANTY SEAL® Graphics warrants to the original consumer purchaser that each new SEAL® Image® Laminator, which proves defective in mater

36 SEAL BRANDS TECHNICAL SERVICE SEAL BRANDS TECHNICAL SERVICE – EUROPE AND ASIA PACIFIC (For technical assistance & service) (Fo

4WORKSPACE / ELECTRICAL REQUIREMENTS • Keep the area around your laminator clear with adequate space around it so you can feed, receive and trim m

5ENVIRONMENT CONDITIONS The following environmental conditions are ideal for the best operation of the laminator. AMBIENT TEMPERATURE The best tem

6ACCESSORIES INCLUDED: • 2-1/2 Square Cap for Stand Legs (4) • Velcro, Black (to secure caps to stand legs) • Snitty Safety Knife • Image Roll C

7 UNPACKING YOUR LAMINATOR • Remove the transport packing and the plastic shrink-wrap the laminator is wrapped in to avoid moisture penetration.

8IMPORTANT SAFEGUARDS SAFETY SYMBOLS USED ON THE LAMINATOR IMPORTANT! Read and make sure you understand these safety and operating guidelines. ROTAT

9SAFETY FEATURES The SEAL® Image® 410 Laminator is designed with safety and protective devices with the user’s safety of utmost consideration. Howe