SEAL 44 Ultra Laminator Dokumentacja

44 Ultra Laminator 44 Ultra Laminator Owner’s Operation Manual

10LAMINATOR FEATURES Figure 7. Laminator Features 1. Automatic Wind-up Idler • Removable idler to support the wind-up core for the release

11CONTROL PANEL LED INDICATOR DESIGN The LED indicators are designed to indicate the on/off status of power, heat, and roller direction. Please se

12OPERATING YOUR LAMINATOR MOTOR CONTROL The speed of the rollers is continuously adjustable between 0 and 1.5 m/min. (0 and 4.8 ft/min.) Pressing

13SET-UP AND OPERATION The following steps outline the basic procedures that have to be used for loading films; setting the nips, webbing the lamin

14SET-UP AND OPERATION SETTING THE UNWIND BRAKE TENSION (Refer to the Features Page for identification.) • Tighten the unwind brake so that it app

15IMAGE GUIDE • To aid with feeding in images, the laminator is provided with an “Image Guide”. • This device can be positioned in front of the

16WEBBING FILMS WITHOUT A RELEASE LINERThe following are the basic webbing procedures for webbing films without a release liner: • Select films sli

17WEBBING FILMS WITH A RELEASE LINER (NORTH AMERICA) The following are the basic webbing procedures for webbing films with a release liner: • Selec

18WEBBING FILMS WITH A RELEASE LINER (EUROPE & ASIA) The following are the basic webbing procedures for webbing films with a release liner: • S

19DECALING This process involves sandwiching an image between a pressure-sensitive or heat-activated laminate on the face of the image and a pressu

2TABLE OF CONT ENTS TABLE OF CONTENTS...

20MOUNTING This process involves mounting previously prepared decals onto a substrate. No films or adhesives are required for this process. To perf

21ENCAPSULATING This process involves completely sealing an image between two films. • Follow the webbing instructions for films specific for your

22PRE-COATING BOARDS This process is used to coat substrates with a self-adhesive coating onto which images can be mounted. Images can then be moun

23USING A ProSEAL® MOUNTING BOARD & POUCH BOARDS USING A ProSEAL MOUNTING BOARD • Refer to the instruction sheet packed with each box of ProSE

24ENCAPSULATING USING A ProSEAL® FLEXIBLE POUCH WITH A ProSEAL® SLED 1. Refer to the instruction sheet packed with each box of ProSEAL Flexible Po

25PROCESS CONTROL SHEET Process: __________________________________ Application Use: ____________________________ Top Unwind Shaft: _______________

26CLEANING YOUR LAMINATOR CLEANING THE LAMINATOR CAUTION! Disconnect the laminator from the power supply before cleaning. • The laminator may be

27TROUBLESHOOTING GUIDE Problem Cause Solution The power LED does not come on, when the laminator is switched on. There is no power. • Check i

28GLOSSARY OF TERMS Decal: An image that has been laminated on top (either heat-activated or pressure-sensitive) with an adhesive backing Film: A

29TECHNICAL SPECIFICATIONS Mechanical Dimensions (H x W x D) 43”H x 58”W x 22”D (1105 mm x 1480 mm x 570 mm) Net Weight 242 lbs. (110 kg) Shippin

3INTRODUCTION Thank you for purchasing a SEAL® 44 Ultra Laminator. We have designed the SEAL 44 Ultra to give you years of reliable service. The 44

30LIMITED WARRANTY SEAL® Graphics warrants to the original consumer purchaser that each new SEAL® Image® Laminator, which proves defective in mater

31

32 SEAL Brands Technical Service SEAL Brands Technical Service – Europe and Asia Pacific (For technical assistance & service) (Fo

4ELECTRICAL SPECIFICATIONS The electrical specifications of the laminators are: North American Version: 110VAC 50/60Hz 16A (Part No. 60959) EU

5Accessories Included: • Wrench 17-24 mm • 10 each Socket head screws • 10 each Star Washers • 2 each Spare Fuses (250V) • Allen key (5 mm) •

6UNPACKING, SET-UP AND INSTALLATION Remove the cardboard box and the plastic bag as described on the outside of the box. Remove and open the boxes

7UNPACKING, SET-UP AND INSTALLATION STEP 3 • Now mount the middle support section between the left-hand and right-hand stand legs, as shown in F

8UNPACKING, SET-UP AND INSTALLATION LAMINATOR PLACEMENT • Your SEAL® 44 Ultra must be setup in the location where it will be used. The stand must

9IMPORTANT SAFEGUARDS SAFETY SYMBOLS USED ON THE LAMINATOR IMPORTANT! Read and make sure you understand these safety and operating guidelines. Rota